Tile laying for decoration and literacy

2022-07-22
  • Detail

Ceramic tile is one of the essential building materials in decoration. It is often used in many spaces such as living room floor, kitchen, bathroom, balcony and so on. Tile paving is an important process in clay tile engineering. What is the process of tile paving? What are the precautions

in decoration, ceramic tile is one of the essential main building materials, which is often used in many spaces such as living room floor, kitchen, bathroom, balcony and so on. Tile paving is an important process in clay tile engineering, but the seemingly simple process has a lot of attention. The following editor will take you to understand the process of tile laying and what precautions are there. 1、 Meaning of ceramic tile paving

ceramic tile is one of the essential main building materials in decoration. It is often used in many spaces such as living room floor, kitchen, bathroom, balcony and so on. Tile paving is an important process in clay tile engineering. The construction technology of tiling is exquisite. Good technology can not only make your indoor space beautiful and flexible, but also save you a lot of money. On the contrary, it will affect the life experience after occupancy and leave worries for the owners

II. Process of tile paving

the basic process of tile paving is: base treatment → Snap line → Pre paving → Paving → Pointing → Clean up

1. Base course treatment:

thoroughly clean the dust and sundries, and there shall be no hollowing, cracking, sanding and other defects. Flatness will fundamentally determine the quality of ceramic tile paving

2. Snap the line:

the vertical line should be found in advance before laying tiles, and the tiles laid on this basis should be uniform in height and vertical and beautiful; In addition, before construction, it is necessary to pop up elevation control lines around the wall and cross lines on the ground to control the separation size of floor tiles

3. Pre paving:

first, strictly select the color, texture, surface smoothness, etc. of the floor tiles on the basis of the drawing design requirements, and then pre pave according to the drawing requirements. Adjust and exchange the size, color and texture errors that may occur in the pre paving until the best effect is achieved, and stack them neatly according to the paving

4. Paving:

1:3 dry and hard cement mortar is selected for paving, and the thickness of mortar is about 20mm. Before paving, wet the back of the floor tile and dry the front. Place the floor tile on the cement mortar as required, and tap the floor tile finish gently with a rubber hammer until it is dense and flat to meet the requirements. The bricklayer applies the mortar evenly to prevent hollowing of the tiles, leaving pores and other tools to grind the cement layer again and then pave it

5. Jointing:

the floor tiles shall be cleaned and jointed 24h after paving. Before jointing, the impurities in the floor tile joints shall be wiped away and the joints shall be pointed with special caulking agent. This is a toilet that is almost finished

6. Cleaning:

clean as you dry during the construction of tiling home decoration. After completion (generally after 24h), use cotton yarn and other things to clean the surface of the floor tile

III. precautions for tile paving

1. Laying of ground tiles:

(1) the tiles should be soaked for half a day before use, subject to the fact that the tiles do not bubble

() 2: the kitchen and bathroom should have a running water slope, without ponding and backflow. If the original waterproof layer is damaged during construction, waterproof treatment must be done. There is no leakage in the 12 hour test of ponding

() 3: after the floor tiles are laid, cover the tile surface with cardboard, etc., and walk on the tile surface at least 24 hours later

2. Laying of wall tiles:

(1) when dealing with the base course, all kinds of dirt on the wall should be cleaned up and watered one day in advance. If the base course is a new wall, when 70% of the cement mortar is dry, bricks should be arranged, lines should be snapped, and wall bricks should be adhered

(2) before pasting, the tiles must be soaked in clean water for more than 2 hours, subject to the fact that the tiles do not bubble, take them out and dry them for use

(3) in case of pipelines, lamp switches, supporting parts of toilet equipment, etc. during paving, the whole brick must be used to cut and match, and it is forbidden to use non whole bricks to put together and paste

in addition:

(1) to reduce the loss of ceramic tiles, we must grasp the whole process. Consumers had better buy well-known brand products and agree on replacement conditions with merchants; When buying, we should also consider the size of ceramic tiles. For an ordinary room of 10-30 square meters, 600× should be paved; 600mm is OK. Don't choose too large ceramic tiles, otherwise the loss will be greater

(2) qualified owners had better often go to the construction site to supervise the work. Once they find that the workers cut the tiles and threw them aside, or broke them, they have to ask clearly to prevent the workers from wasting them at will

the above is all about the steps and precautions of tile paving. I hope it will be helpful to you. If you want to know more about decoration, please pay attention to the decoration information channel

广州牛皮癣医院

郑州乳腺医院

成都妇科医院

Copyright © 2011 JIN SHI